Safety Data Sheet for SimuBone - 3D Printing Filament | Rev1Tech

SimuBone SAFETY DATA SHEET

SAFETY DATA SHEET

Product Identification

Product Name:       SimuBone

Product Use:         3D Printing Filament

Manufacturer/Supplier: Rev1Tech

Address:                2901 Auburn Rd, Auburn Hills, MI 48326

Contact Email:       info@rev1tech.com

Telephone:           +248-707-2950

Emergency Telephone Number: +248-707-2950

1. PRODUCT AND SUPPLIER INFORMATION

Product Name: SimuBone

Chemical Name: Polylactic Acid (PLA)

Recommended Use: Additive manufacturing

Supplier Information:

  • Rev1Tech
  • 904 36th Street, Suite B
  • Grand Rapids MI 49500 USA
  • Phone: +248-707-2950
  • Email: info@rev1tech.com

2. HAZARDS IDENTIFICATION

Regulation (EC) NO 1272/2008: Not classified as a dangerous product

Physical Hazards: None

OSHA Regulatory Status: This product is not considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)

3. COMPOSITION/INFORMATION ON INGREDIENTS

Components CAS No. Concentration Range (%)
PLA Resin 9051-89-02 >85%
Remainder of formulation has been withheld as a trade secret

4. EMERGENCY FIRST AID

  • Eyes: Flush with water. Consult physician if symptoms persist.
  • Skin Contact: Wash with soap and water. For thermal burns from molten polymer, immediately flush with cold water. Do not attempt to remove cooled polymer from skin. Obtain medical attention.
  • Inhalation: Leave exposed area and seek fresh air. If irritation persists seek medical attention.
  • Ingestion: Not likely due to nature of product. If ingested, drink plenty of water. Do not induce vomiting. Consult a physician if symptoms persist.

5. FIRE AND EXPLOSION HAZARD

  • Extinguishing Media: Water spray, dry powder, and foam. Carbon dioxide (CO2)
  • Safety Precautions: Persons exposed to products of combustion should wear NIOSH approved self-contained breathing apparatus and full protective equipment.

16. MISCELLANEOUS INFORMATION

Prepared by: Business Management

Issued: 08/01/2022

This information set forth herein has been gathered from standard reference materials and/or supplier test data and is, to the best knowledge and belief of Rev1Tech, accurate and reliable. Such information is offered solely for your consideration, investigation and verification, and it is not suggested or guaranteed that the hazard precautions or procedures mentioned are the only ones which exist. Rev1Tech makes no warranties, expressed or implied, with respect to the use of such information or the use of the specific material identified herein in combination with any other material or process, and assumes no responsibility therefore.


Click here to shop SimuBone Bone Modeling Filament.

END OF SDS


    • Related Articles

    • PolyMax™ PLA Safety Data Sheet

      PolyMax™ PLA Safety Data Sheet According to Hazard Communication Standard (29 CFR 1910.1200) Version 1.0 | Issue date: 07/29/2019 | Revision date: 07/29/2019 | SDS record number: CSSS-TCO-010-132036 1. Product and Company Identification Product Name ...

    • SimuBone™ Technical Data Sheet

      Technical Data Sheet SimuBone™ Bone Simulation Filament Physical Properties Standard Unit Typical Value Density ISO 1183 g/cc 1.34 Mechanical Properties . Standard Unit Typical Value Tensile Strength, Break ISO 527 MPa 65 Tensile Modulus ISO 527 . ...

    • PolySmooth Safety Data Sheet

      Safety Data Sheet According to Hazard Communication Standard (29 CFR 1910.1200) 1. Identification Product Name: PolySmooth Product Use: 3d Printing filament Manufacturer/Supplier: JF Polymers (Suzhou) Co., Ltd. Address: 2901 Auburn Rd, Auburn Hills, ...

    • PolyFlexTPU95 Safety Data Sheet

      Identification Product Name PolyFlex TPU95 Product Use 3D Printing Filament Manufacturer/Supplier JF Polymers (Suzhou) Co., Ltd. Address 2901 Auburn Rd, Auburn Hills, MI 48326 Contact Email info@rev1tech.com Telephone +248-707-2950 Emergency ...

    • PolySonic PLA Pro Safety Data Sheet

      Safety Data Sheet 1. Product and Company Identification Product Name PolySonic PLA Pro Product Use 3D Printing Filament Manufacturer/Supplier JF Polymers (Suzhou) Co., Ltd. Address 2901 Auburn Rd, Auburn Hills, MI 48326 Contact Email ...