PolyFlex TPU95 Technical Data Sheet
Technical Data Sheet
Identification
| Product Name |
PolyFlex TPU95 |
| Product Use |
3D Printing Filament |
| Manufacturer/Supplier |
JF Polymers (Suzhou) Co., Ltd. |
| Address |
2901 Auburn Rd, Auburn Hills, MI 48326 |
| Contact Email |
info@rev1tech.com |
| Telephone |
+248-707-2950 |
| Emergency Telephone Number |
+248-707-2950 |
Material Properties
| Property |
Standard |
Value |
| Density |
ISO1183, GB/T1033 |
1.20-1.24 g/cm3 at 23 °C |
| Melt index |
210°C, 1.2 kg |
3-6 g/10min |
| Light transmission |
N/A |
N/A |
| Flame retardancy |
N/A |
N/A |
| Effect of weak acids |
N/A |
Not resistant |
| Effect of strong acids |
N/A |
Not resistant |
| Effect of weak alkalis |
N/A |
Not resistant |
| Effect of strong alkalis |
N/A |
Not resistant |
| Effect of organic solvent |
N/A |
No data available |
| Effect of oils and grease |
N/A |
No data available |
| Equilibrium water absorption |
N/A |
0.82% |
Mechanical Properties
| Property |
Standard |
Value |
| 100% modulus (X-Y) |
ISO 37, GB/T 528 |
9.4 ± 0.3 MPa |
| Young’s modulus (X-Y) |
ISO 37, GB/T 528 |
29 ± 2.8 MPa |
| Elongation at break (X-Y) |
ISO 37, GB/T 528 |
330.1 ± 14% |
| Shore hardness |
ISO 7619-1, GB/T 531.1 |
95A |
Printing Settings
| Parameter |
Value |
| Nozzle temperature |
210 – 230 (℃) |
| Build surface material |
BuildTak®, Glass, Blue Tape |
| Build surface treatment |
PVA or PVP glue, Magigoo |
| Build plate temperature |
25 - 60 (˚C) |
| Cooling fan |
ON |
| Printing speed |
20-40 (mm/s) |
| Raft separation distance |
0.2 (mm) |
| Retraction distance |
3 (mm) |
| Retraction speed |
40 (mm/s) |
| Environmental temperature |
Room temperature |
| Threshold overhang angle |
35 (˚) |
| Recommended support material |
PolySupport™ and PolyDissolve™ S1 |
Additional Printing Parameters
| Parameter |
Value |
| Printing temperature |
225 °C |
| Bed temperature |
30 °C |
| Shell |
2 |
| Top & bottom layer |
4 |
| Infill |
100% |
| Environmental temperature |
25 °C |
| Cooling fan |
ON |
The typical values presented in this data sheet are intended for reference and comparison purposes only. They
should not be used for design specifications or quality control purposes. Actual values may vary significantly with
printing conditions. End-use performance of printed parts depends not only on materials, but also on part design,
environmental conditions, printing conditions, etc. Product specifications are subject to change without notice.
Each user is responsible for determining the safety, lawfulness, technical suitability, and disposal/recycling
practices of Polymaker materials for the intended application. Rev1Tech makes no warranty of any kind, unless
announced separately, to the fitness for any use or application. Rev1Tech shall not be made liable for any damage,
injury, or loss induced from the use of Rev1Tech materials in any application.
Click here to shop PolyFlexTPU95.
Related Articles
PolyFlex TPU90 Technical Data Sheet
PolyFlex TPU90 Technical Data Sheet Product Identification Product Name PolyFlex TPU90 Product Use 3D Printing Filament Manufacturer/Supplier JF Polymers (Suzhou) Co., Ltd. Address 2901 Auburn Rd, Auburn Hills, MI 48326 Contact Email ...
PolyFlex TPU95-HF Tech Data Sheet
PolyFlex TPU95-HF Tech Data Sheet Product Name: PolyFlex TPU95-HF Product Use: 3D Printing Filament Manufacturer/Supplier: JF Polymers (Suzhou) Co., Ltd. Address: 2901 Auburn Rd, Auburn Hills, MI 48326 Contact Email: info@rev1tech.com Telephone: ...
Technical Data Sheet: 3DXMAX™ ASA 3D Printing Filament
Technical Data Sheet: 3DXMAX™ ASA 3D Printing Filament TDS Rev 3.0 Physical Properties Property Standard Unit Typical Value Density ISO 1183 g/cc 1.07 Mechanical Properties Property Standard Unit Typical Value Tensile Strength, Break ISO 527 MPa 45 ...
PolyFlex TPU90 Safety Data Sheet
PolyFlex TPU90 Safety Data Sheet Product Identification Product Name PolyFlex TPU90 Product Use 3D Printing Filament Manufacturer/Supplier JF Polymers (Suzhou) Co., Ltd. Address 2901 Auburn Rd, Auburn Hills, MI 48326 Contact Email info@rev1tech.com ...
PolyMide_PA12-CF Technical Data Sheet
Product Technical Data Sheet Product Name: PolyMide_PA12-CF Product Use: 3D Printing Filament Manufacturer/Supplier: JF Polymers (Suzhou) Co., Ltd. Address: 2901 Auburn Rd, Auburn Hills, MI 48326 Contact Email: info@rev1tech.com Telephone: ...