| Product Name | PolyFlex TPU90 |
|---|---|
| Product Use | 3D Printing Filament |
| Manufacturer/Supplier | JF Polymers (Suzhou) Co., Ltd. |
| Address | 2901 Auburn Rd, Auburn Hills, MI 48326 |
| Contact Email | info@rev1tech.com |
| Telephone | +248-707-2950 |
| Emergency Telephone Number | +248-707-2950 |
PolyFlex™ TPU90, created from Covestro’s Addigy® family, is a thermoplastic polyurethane (TPU) based filament designed to provide great flexibility without compromising on printing speed. It also has the ability to resist ultra-violet (UV) light or sunlight.
| Property | Test Method | Typical Value |
|---|---|---|
| Density | ISO1183, GB/T1033 | 1.12 g/cm3 at 23 °C |
| Melt index | 185°C, 1.2 kg | 6.1 g/10min |
| Light transmission | N/A | N/A |
| Flame retardancy | N/A | N/A |
| Effect of weak acids | Not resistant | |
| Effect of strong acids | Not resistant | |
| Effect of weak alkalis | Not resistant | |
| Effect of strong alkalis | Not resistant | |
| Effect of organic solvent | No data available | |
| Effect of oils and grease | No data available | |
| Equilibrium water absorption (%) | 0.67% |
| Property | Test Method | Typical Value |
|---|---|---|
| 100% modulus (X-Y) | ISO 37, GB/T 528 | 6.17 ± 0.19 MPa |
| Tensile strength (X-Y) | ISO 37, GB/T 528 | 30.0 ± 0.66 MPa |
| Elongation at break (X-Y) | ISO 37, GB/T 528 | 586.8 ± 15.3 % |
| Shore hardness | ISO 7619-1, GB/T 531.1 | 90A |
* Based on 0.4 mm nozzle and Simplify 3D v.4.0. Printing conditions may vary with different nozzle diameters.
| Parameter | Typical Value |
|---|---|
| Nozzle temperature | 210 – 230 ℃ |
| Build surface material | BuildTak®, Glass, Blue Tape |
| Build surface treatment | PVA or PVP glue, Magigoo |
| Build plate temperature | 25 - 60 ˚C |
| Cooling fan | ON |
| Printing speed | 30-60 mm/s |
| Raft separation distance | 0.2 mm |
| Retraction distance | 3 mm |
| Retraction speed | 40 mm/s |
| Environmental temperature | Room temperature |
| Threshold overhang angle | 35 ˚ |
| Recommended support material | PolySupport™ and PolyDissolve™ S1 |
| Parameter | Typical Value |
|---|---|
| Printing temperature | 220 °C |
| Bed temperature | 50 °C |
| Shell | 2 |
| Top & bottom layer | 4 |
| Infill | 100% |
| Environmental temperature | 25 °C |
| Cooling fan | ON |
*All specimens were conditioned at room temperature for 24h prior to testing
The typical values presented in this data sheet are intended for reference and comparison purposes only. They should not be used for design specifications or quality control purposes. Actual values may vary significantly with printing conditions. End-use performance of printed parts depends not only on materials, but also on part design, environmental conditions, printing conditions, etc. Product specifications are subject to change without notice.
Each user is responsible for determining the safety, lawfulness, technical suitability, and disposal/recycling practices of Rev1tech materials for the intended application. Rev1tech makes no warranty of any kind, unless announced separately, to the fitness for any use or application. Rev1tech shall not be made liable for any damage, injury or loss induced from the use of Rev1tech materials in any application.
Click here to shop polyflex-TPU90.