PolyMide PA6 GF Technical Data Sheet
PolyMide PA6 GF Technical Data Sheet
Material Properties
| Property |
Value |
Standard |
| Density |
1.2 g/cm³ at 23°C |
ISO1183, GB/T1033 |
| Melt Index |
15.9 g/10min |
300°C, 2.16 kg |
Thermal Properties
| Property |
Value |
Standard |
| Glass Transition Temperature |
70.4 °C |
DSC, 10°C/min |
| Melting Temperature |
214.5 °C |
DSC, 10°C/min |
Mechanical Properties
| Property |
Value |
Standard |
| Young’s Modulus (X-Y) |
4431 ± 184 MPa |
ISO 527, GB/T 1040 |
| Tensile Strength (X-Y) |
84.5 ± 2.1 MPa |
ISO 527, GB/T 1040 |
Printing Guidelines
- Abrasion of the brass nozzle happens frequently when printing PolyMide™ PA6-GF. Normally, the life of a brass nozzle would be approximately 9h. A wear-resistance nozzle, such as hardened steel and ruby nozzle, is highly recommended to be used with PolyMide™ PA6-GF.
- PolyMide™ PA6-GF is sensitive to moisture and should always be stored and used under dry conditions (relative humidity below 20%).
- If PolyMide™ PA6-GF is used as the support material for itself, please remove the support structure before excessive moisture absorption. Otherwise, the support structure can be permanently bonded to the model.
- After the printing process, it is recommended to anneal the model in the oven at 80 - 100°C for 6 hours.
Printing Parameters
| Parameter |
Value |
| Nozzle Temperature |
280 – 300 °C |
| Build Surface Material |
BuildTak®, Glass, Blue Tape |
| Build Surface Treatment |
Glue |
The typical values presented in this data sheet are intended for reference and comparison purposes only. They should not be used for design specifications or quality control purposes. Actual values may vary significantly with printing conditions. End-use performance of printed parts depends not only on materials but also on part design, environmental conditions, printing conditions, etc. Product specifications are subject to change without notice.
Each user is responsible for determining the safety, lawfulness, technical suitability, and disposal/recycling practices of Rev1Tech materials for the intended application. Rev1Tech makes no warranty of any kind, unless announced separately, to the fitness for any use or application. Rev1Tech shall not be made liable for any damage, injury or loss induced from the use of Rev1Tech materials in any application.
Click here to shop PolyMide_PA6_GF.
Related Articles
PolyMide PA6-CF Technical Data Sheet
PolyMide PA6-CF Technical Data Sheet Identification Product Name PolyMide_PA6-CF Product Use 3D Printing Filament Manufacturer/Supplier JF Polymers (Suzhou) Co., Ltd. Address 2901 Auburn Rd, Auburn Hills, MI 48326 Contact Email info@rev1tech.com ...
PolyMide_PA12-CF Technical Data Sheet
Product Technical Data Sheet Product Name: PolyMide_PA12-CF Product Use: 3D Printing Filament Manufacturer/Supplier: JF Polymers (Suzhou) Co., Ltd. Address: 2901 Auburn Rd, Auburn Hills, MI 48326 Contact Email: info@rev1tech.com Telephone: ...
PolyMide CoPA Technical Data Sheet
PolyMide CoPA Technical Data Sheet Identification Product Name PolyMide_CoPA Product Use 3D Printing Filament Manufacturer/Supplier JF Polymers (Suzhou) Co., Ltd. Address 2901 Auburn Rd, Auburn Hills, MI 48326 Contact Email info@rev1tech.com ...
PolyMide™ CoPA Safety Data Sheet
PolyMide CoPA Safety Data Sheet 1. Identification Product Name PolyMide_CoPA Product Use 3D Printing Filament Manufacturer/Supplier JF Polymers (Suzhou) Co., Ltd. Address 2901 Auburn Rd, Auburn Hills, MI 48326 Contact Email info@rev1tech.com ...
PolySmooth Tech Data Sheet
Technical Data Sheet Product Identification Product Name PolySmooth Product Use 3D Printing Filament Manufacturer/Supplier JF Polymers (Suzhou) Co., Ltd. Address 2901 Auburn Rd, Auburn Hills, MI 48326 Contact Email info@rev1tech.com Telephone ...