1. PRODUCT AND SUPPLIER INFORMATION

Product Name	FibreX™ PA6+GF30
Product Use	3D Printing Filament
Manufacturer/Supplier	Rev1Tech
Address	904 36th Street, Suite B, Grand Rapids MI 49500 USA 2901 Auburn Rd, Auburn Hills, MI 48326
Contact Email	info@rev1tech.com
Telephone	+248-707-2950
Emergency Telephone Number	+248-707-2950

2. HAZARDS IDENTIFICATION

Regulation (EC) NO 1272/2008: Not classified as a dangerous product

Physical Hazards: None

OSHA Regulatory Status: This product is not considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)

3. COMPOSITION/INFORMATION ON INGREDIENTS

Components	CAS No.	Concentration Range (%)
Polyamide Resin	25038-54-4	65 - 68
Glass Fiber Reinforcement	65997-17-3	28 - 32
Nylon-Based Colorant	Proprietary	1 - 2

4. EMERGENCY FIRST AID

• Eyes: Flush with water. Consult a physician if symptoms persist.
• Skin Contact: Wash with soap and water. For thermal burns from molten polymer, immediately flush with cold water. Do not attempt to remove cooled polymer from skin. Obtain medical attention.
• Inhalation: Leave exposed area and seek fresh air. If irritation persists, seek medical attention.
• Ingestion: Not likely due to the nature of the product. If ingested, drink plenty of water. Do not induce vomiting. Consult a physician if symptoms persist.

5. FIRE AND EXPLOSION HAZARD

Extinguishing Media: Water spray, dry powder, and foam. Carbon dioxide (CO2).

Safety Precautions: Persons exposed to products of combustion should wear NIOSH approved self-contained breathing apparatus and full protective equipment.

6. ACCIDENTAL RELEASE MEASURES

Spill or release: Clean up by vacuuming or sweeping to prevent falls. If molten, allow material to cool and place into an appropriate container for disposal.

7. HANDLING AND STORAGE CONDITIONS

Precautions: Store in a dry, sprinkler-equipped warehouse. Product as shipped is not a combustible dust. Mechanical handling can cause the formation of dust. To reduce the risk of dust explosion, do not permit dust to accumulate.

Waste Disposal: Dispose of in accordance with applicable federal, state, and local regulations.

8. EXPOSURE AND PROTECTION INFORMATION

• Exposure Limits: This product does not contain any hazardous materials with occupational exposure limits established by region-specific regulatory bodies.
• Respiratory Protection: A NIOSH approved respirator is recommended for protection against processing polymeric fumes or from dust generated from grinding, sanding, or sawing operations.
• Ventilation: Local exhaust is preferred.
• Protection Gloves: Canvas or cotton gloves are recommended.
• Eye Protection: Safety glasses with side shields are recommended.
• Other: No protective equipment is needed under normal use conditions.

9. PHYSICAL/CHEMICAL DATA

Form	Solid
Appearance	Black Filament
Odor	Slight
Freezing Point	N/A
Solubility in Water	Insoluble
Specific Gravity	>1
% Volatile	N/A
Boiling Range	N/A
Vapor Pressure (MM HG)	Negligible
Melting Point	210 - 220°C

10. STABILITY AND REACTIVITY

• Polymerization conditions to avoid: None
• Chemical Stability: Stable under normal conditions
• Conditions to avoid: Incompatible materials, including strong oxidizing agents
• Hazardous decomposition byproducts: Thermal decomposition can yield intense heat, dense smoke, phenols, hydrogen cyanide, carbon dioxide, and carbon monoxide.

11. TOXICOLOGICAL INFORMATION

No specific toxicological information is available.

12. ECOLOGICAL INFORMATION

No specific ecological information is available.

13. DISPOSAL

Waste Disposal: Waste or unused product may be discarded in accordance with state, federal, and local regulations.

14. TRANSPORT INFORMATION

Land Transport (DOT): Non-Regulated

Sea Transport (IMDG): Non-Regulated

Air Transport (ICAO/IATA): Non-Regulated

15. REGULATORY INFORMATION

TSCA	Complies [All ingredients]
EINECS/ELINCS	N/A
DSL/NDSL	Complies
PICCS	N/A
ENCS	Complies
IECSC	Complies
AICS	Complies
KECL	Complies
ROHS	Complies
REACH	Complies

16. MISCELLANEOUS INFORMATION

Prepared by: Business Management

Issued: 08/01/2022

This information set forth herein has been gathered from standard reference materials and/or supplier test data and is, to the best knowledge and belief of Rev1Tech, accurate and reliable. Such information is offered solely for your consideration, investigation, and verification, and it is not suggested or guaranteed that the hazard precautions or procedures mentioned are the only ones which exist. Rev1Tech makes no warranties, expressed or implied, with respect to the use of such information or the use of the specific material identified herein in combination with any other material or process, and assumes no responsibility therefore.