SAFETY DATA SHEET
CarbonX™ PEEK+CF10 Carbon Fiber Reinforced PEEK 3D Printing Filament
| Product Name |
CarbonX PEEK+CF10 |
| Product Use |
3D Printing Filament |
| Manufacturer/Supplier |
Rev1Tech |
| Address |
904 36th Street, Suite B, Grand Rapids, MI 49500, USA |
| Contact Email |
info@rev1tech.com |
| Telephone |
+248-707-2950 |
| Emergency Telephone Number |
+248-707-2950 |
2. HAZARDS IDENTIFICATION
Regulation (EC) NO 1272/2008: Not classified as a dangerous product
Physical Hazards: None
OSHA Regulatory Status: This product is not considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
| Component |
CAS No. |
Concentration Range (%) |
| PA12 Resin |
Confidential |
>80 |
| Carbon Fiber |
308063-67-4 |
<20 |
4. EMERGENCY FIRST AID
- Eyes: Flush with water. Consult physician if symptoms persist.
- Skin Contact: Wash with soap and water. For thermal burns from molten polymer, immediately flush with cold water. Do not attempt to remove cooled polymer from skin. Obtain medical attention.
- Inhalation: Leave exposed area and seek fresh air. If irritation persists, seek medical attention.
- Ingestion: Not likely due to nature of product. If ingested, drink plenty of water. Do not induce vomiting. Consult a physician if symptoms persist.
5. FIRE AND EXPLOSION HAZARD
- Extinguishing Media: Water spray, dry powder, and foam. Carbon dioxide (CO2).
- Safety Precautions: Persons exposed to products of combustion should wear NIOSH approved self-contained breathing apparatus and full protective equipment.
6. ACCIDENTAL RELEASE MEASURES
- Spill or release: Clean up by vacuuming or sweeping to prevent falls. If molten, allow material to cool and place into an appropriate container for disposal.
7. HANDLING AND STORAGE CONDITIONS
- Precautions: Store in a dry, sprinkler-equipped warehouse. Product as shipped is not a combustible dust. Mechanical handling can cause the formation of dusts. To reduce the risk for dust explosion, do not permit dust to accumulate.
- Waste Disposal: Dispose in accordance with applicable federal, state, and local regulations.
- Exposure Limits: This product does not contain any hazardous materials with occupational exposure limits established by the region-specific regulatory bodies.
- Respiratory Protection: A NIOSH-approved respirator is recommended for protection against processing polymeric fumes or from dust generated from grinding, sanding, or sawing operations.
- Ventilation: Local exhaust is preferred.
- Protection Gloves: Canvas or cotton gloves are recommended.
- Eye Protection: Safety glasses with side shields are recommended.
- Other: No protective equipment is needed under normal use conditions.
9. PHYSICAL/CHEMICAL DATA
| Property |
Value |
| Form |
Solid |
| Appearance |
Black Filament |
| Odor |
Slight |
| Freezing Point |
N/A |
| Solubility in Water |
Insoluble |
| Specific Gravity |
>1 |
| % Volatile |
N/A |
| Boiling Range |
N/A |
| Vapor Pressure (MM HG) |
Negligible |
| Melting Point |
178°C |
10. STABILITY AND REACTIVITY
- Polymerization conditions to avoid: None
- Chemical Stability: Stable under normal conditions
- Conditions to avoid: Incompatible materials, including strong oxidizing agents
- Hazardous decomposition byproducts: Thermal decomposition can yield intense heat, dense smoke, phenols, hydrogen cyanide, carbon dioxide, and carbon monoxide.
No specific toxicological information is available.
No specific ecological information is available.
13. DISPOSAL
Waste or unused product may be discarded in accordance with state, federal, and local regulations.
- Land Transport (DOT): Non-Regulated
- Sea Transport (IMDG): Non-Regulated
- Air Transport (ICAO/IATA): Non-Regulated
- TSCA: Complies
- ROHS: Complies
- EINECS/ELINCS: N/A
- REACH: Complies
- DSL/NDSL: Complies
- PICCS: N/A
- ENCS: Complies
- IECSC: Complies
- AICS: Complies
- KECL: Complies
Prepared by: Business Management
Issued: 08/01/2022
This information set forth herein has been gathered from standard reference materials and/or supplier test data and is, to the best knowledge and belief of Rev1Tech, accurate and reliable. Such information is offered solely for your consideration, investigation, and verification, and it is not suggested or guaranteed that the hazard precautions or procedures mentioned are the only ones which exist. Rev1Tech makes no warranties, expressed or implied, with respect to the use of such information or the use of the specific material identified herein in combination with any other material or process, and assumes no responsibility therefore.